DAC curve calculator: rate a UT echo against your reference points

Enter the sound path or depth and screen height of each reference echo, then an indication's position, height and any gain change. You get the curve height at that position, the echo in dB above or below DAC and as a percent of DAC, with optional −6 dB and −14 dB lines.

Plot a DAC curve and rate an indication

Results update as you type. Enter every height at the reference gain the curve was built at.

Reference points

2 to 6 points, in any order. They are sorted by position and joined with straight lines.

Indication

Gain: enter how many dB more (positive) or less (negative) than the reference gain the indication was read at. Leave 0 if the gain was not changed.

Indication re DAC
−5.55 dB
% of DAC
52.8%
DAC at this position
57% FSH
Indication at reference gain
30.07% FSH
-6 dB line at this position
28.57% FSH
-14 dB line at this position
11.37% FSH

Steps

Reference gain: A' = A × 10^(−ΔG ÷ 20) = 60 × 10^(−6 ÷ 20) = 30.07% FSH. The echo was read with extra gain, so it is smaller at the reference gain.

DAC between 20 mm (64%) and 30 mm (50%), on a straight line: 64 + (25 − 20) ÷ (30 − 20) × (50 − 64) = 57% FSH.

dB re DAC = 20 × log10(30.07 ÷ 57) = −5.55 dB, and %DAC = 100 × 30.07 ÷ 57 = 52.8%. The echo is below the curve.

DAC curve through the reference points, with the indication4 reference points from 10 to 40 mm, joined by straight lines. Indication at 25 mm, 30.07% FSH at the reference gain. The curve there is 57% FSH, so the indication is −5.55 dB re DAC.02040608010010 mm40 mmSound path or depth (mm)
% FSH up the side at the reference gain. Solid line: DAC through your points. Dashed: −6 dB. Dotted: −14 dB. The bar and square: the indication at the reference gain. Not drawn to any code's format.

For study and calculation practice only. Your written procedure sets the reference level, the curve and any recording or acceptance level; a qualified person makes the call.

The curve is straight between points and stops at the first and last point. One probe, one set of instrument settings and one material, as the curve was built.

Free 10-question check

Studying for UT L2? Take the free 10-question check to see exactly which topics to fix first, then close the gaps with the Angle Beam course.

Free UT L2 check

Or read a full free lesson first (no signup).

Studying with a coworker? Send them the free check.

How to use the DAC curve calculator

  1. Pick the position unit. Use sound path or depth for every point and the indication, not a mix of the two.
  2. Enter 2 to 6 reference points: where each reference echo peaked and its height in percent full-screen height (% FSH), all at the reference gain. Order does not matter.
  3. Enter the indication's position and its peak height as read on the screen.
  4. If you added or removed gain to read the indication, enter the change in dB: positive for more gain than the reference, negative for less.

The formulas

  • The curve between two points. DAC(s) = A1 + (s − s1) ÷ (s2 − s1) × (A2 − A1), for a position s between neighboring points s1 and s2. The calculator joins the marks with straight lines, as the DAC curve guide describes the curve being drawn, and never extends it past the first or last point.
  • Back to the reference gain: A' = A × 10^(−ΔG ÷ 20). Every 6 dB of extra gain roughly doubles an echo, so an echo read 6 dB hot is about half as tall at the reference gain.
  • dB re DAC = 20 × log10(A' ÷ DAC(s)) and %DAC = 100 × A' ÷ DAC(s). The 20 × log10 form for two screen heights is the decibel definition in Evident's flaw detection tutorial glossary.
  • −6 dB and −14 dB lines: DAC × 10^(−6 ÷ 20) and DAC × 10^(−14 ÷ 20), about 50.1% and 20.0% of the curve. Evident's tutorial shows these two extra curves below a reference curve as an example. Which lines your procedure uses, if any, is up to the procedure.

How the reference points are made

Evident's tutorial says DAC is usually set up with a series of reference reflectors of one size at different depths, from a bought distance/amplitude block set or a block users make themselves. With the probe and instrument settings fixed, peak each reflector in turn and note its position and height. Those pairs are the points you enter here. The curve belongs to that probe, those settings and that material, so a change to any of them means a new curve.

Worked example 1: an echo on a reference point

Invented numbers. Points at 10, 20, 30 and 40 mm read 80%, 64%, 50% and 40% FSH. An indication at 20 mm peaks at 64% FSH with no gain change. The curve there is 64%, so dB re DAC = 20 × log10(64 ÷ 64) = 0 dB and the echo is 100% DAC.

Worked example 2: half the curve height

Same points. At 30 mm the curve is 50% FSH and an indication peaks at 25% with no gain change. dB re DAC = 20 × log10(25 ÷ 50) = −6.02 dB, or 50% DAC. Halving an amplitude is always about −6 dB.

Worked example 3: between two points, read with extra gain

Same points. An indication at 25 mm peaks at 60% FSH, read 6 dB above the reference gain. The curve at 25 mm is 64 + (25 − 20) ÷ (30 − 20) × (50 − 64) = 57% FSH. At the reference gain the echo is 60 × 10^(−6 ÷ 20) = 30.07% FSH. dB re DAC = 20 × log10(30.07 ÷ 57) = −5.55 dB, or 52.8% DAC. Forget the gain change and you would rate the echo 1.05 times the curve, above it instead of below.

Move that indication to 45 mm and the calculator gives no rating, because the last point is at 40 mm and the curve is not extended. Add a reference point at or beyond 45 mm instead.

These are original arithmetic examples, not exam questions. The same decibel steps are in the 6 dB and 20 dB rules, and the decibel calculator converts any ratio.

Common mistakes

  • Wrong sign on the gain change. Extra gain makes the echo taller, so it must come off: A' = A × 10^(−ΔG ÷ 20).
  • Reading a clipped echo. An echo above 100% FSH has no true height. Drop the gain, read it on screen and enter the gain change.
  • Extending the curve. Past the last point you have no reference echo. Add one rather than guess.
  • Mixing sound path and depth. Points and the indication must use the same measure.
  • Using a stale curve. A new probe, couplant, gain setting or material means rebuilding or verifying the curve. Attenuation and the near field explain why it changes.

DAC curve questions

What is a DAC curve in ultrasonic testing?

DAC stands for distance amplitude correction. The curve joins the echo heights from reflectors of one size at several distances from the probe. The same reflector gives a lower echo farther away, mostly from attenuation and beam spread, so the curve slopes down. Evident's flaw detection tutorial says an echo from a reflector the same size as the reference ones matches the curve height at any depth, and a larger or smaller one sits above or below it.

How do you work out dB above or below DAC?

Bring the echo to the reference gain first: A' = A × 10^(−ΔG ÷ 20), where ΔG is how many dB above the reference gain it was read at. Then dB re DAC = 20 × log10(A' ÷ DAC), using the curve height at the echo's own position. An echo at half the curve height is about −6 dB, and %DAC = 100 × A' ÷ DAC.

Does this calculator say whether to record or reject an indication?

No. Your written procedure sets the reference level, how the curve is built and any recording or acceptance level, and a qualified person makes the call. This page does the arithmetic only and holds no acceptance level from any code or standard.

Related: the UT Level II formulas guide for the rest of the UT arithmetic, and the UT beam calculator for the near field and beam spread behind the curve's shape.

Join 2 to 6 reference echoes with straight lines, bring an indication back to the reference gain with A' = A × 10^(−ΔG ÷ 20), and compare it with the curve at its own position in dB and percent. A study aid; your written procedure governs the curve and every acceptance call.

Try one free question

Try one question

Question 1 of the free 10-question check on UT L2. No signup. Then ask Echo, the AI study assistant, why the answer is right and the others are wrong.

Question 1 of 10 · free checkUntimed

Discontinuity Detection

A planar reflector gives its highest echo amplitude when the beam strikes it

Press A-D or 1-4 to choose an answer while this question is on screen.

Choose an answer to begin

Email me the UT L2 study plan

Done with DAC Curve Calculator for Ultrasonic Testing? See what to study next: a week-by-week plan from today to your exam, weighted to the published exam outline. It shows here at once and a copy comes by email.

Ask Echo before you buy AI your AI study assistant

See what's on the UT L2 exam, test yourself with 5 quick questions, or find the plan that fits you.

Published references

Checked 21 Nov 2026. The straight-line curve and the indication arithmetic are standard algebra on the decibel definition.

From the blog

Practice UT Level II fundamentals

You just built a DAC curve and rated an echo against it. The free 10-question check shows which Level II topics to fix first, no signup. The Angle Beam course drills them and explains every answer.

Free NDT Level II check

The UT L2 course

Available now · instant access

The UT L2 course

  • 7modules of lessonsEvery task on the outline
  • 5full-length timed exams50 questions in 120 minutes each
  • 387practice questionsEach one explained
  • 5worked calculationsStep by step
  • 1week-by-week study planSet to your exam date

Turn a practice answer into a study step. In untimed practice, ask Echo AI about any question you answer, follow up, then see your weakest topics and what to drill next.

NDT UT Level II General course$149

Terms and refunds · Secure checkout by Stripe · Billed by Nori Software

See the course

Compare plans

Every answer comes with a full explanation.

By the Angle Beam editorial team. Report an error.

Add this calculator to your site

Copy this HTML with its attribution link. It embeds the calculator and adds no external script tag.