Ultrasonic velocity of steel, water and more
Sound travels about 5,890 m/s (0.232 in/µs) as a longitudinal wave and 3,240 m/s (0.128 in/µs) as a shear wave in 1020 steel. In aluminum the figures are 6,320 and 3,130 m/s, and in water at 20 °C sound travels about 1,480 m/s. These are typical values from Table 2 of Evident's ultrasonic transducer Technical Notes, and the chart below gives twelve common materials in both unit systems.
Ultrasonic velocity chart
Longitudinal (L) and shear (S) velocities. The in/µs columns are m/s divided by 25,400. Liquids carry no shear wave, so their shear cells read none.
| Material | L (m/s) | L (in/µs) | S (m/s) | S (in/µs) |
|---|---|---|---|---|
| Steel 1020 | 5,890 | 0.232 | 3,240 | 0.128 |
| Steel 4340 | 5,850 | 0.230 | 3,240 | 0.128 |
| Stainless steel 302 | 5,660 | 0.223 | 3,120 | 0.123 |
| Austenitic stainless steel 347 | 5,740 | 0.226 | 3,090 | 0.122 |
| Aluminum | 6,320 | 0.249 | 3,130 | 0.123 |
| Titanium Ti 150A | 6,100 | 0.240 | 3,120 | 0.123 |
| Copper | 4,660 | 0.183 | 2,260 | 0.089 |
| Nickel, pure | 5,630 | 0.222 | 2,960 | 0.117 |
| Brass, naval | 4,430 | 0.174 | 2,120 | 0.083 |
| Acrylic resin (Perspex) | 2,730 | 0.107 | 1,430 | 0.056 |
| Water (20 °C) | 1,480 | 0.058 | none | none |
| Glycerin | 1,920 | 0.076 | none | none |
To work in mm/µs, divide m/s by 1,000: steel 1020 is 5.89 mm/µs longitudinal and 3.24 mm/µs shear.
Why shear runs at about half of longitudinal
A longitudinal wave squeezes and stretches the material along its path. A shear wave slides each layer sideways, and a solid resists that sideways slide less than it resists squeezing, so the shear wave is slower. In every solid in the chart, shear runs at 0.48 to 0.55 of longitudinal. A liquid has no resistance to sliding at all, which is why water and glycerin have no shear value. The pair of velocities is so closely tied to stiffness that the Technical Notes (Equations 15 to 17, p. 8) use a measured longitudinal and shear velocity, with density, to work out Poisson's ratio, Young's modulus and the shear modulus. The shear vs longitudinal wave guide covers particle motion and which probe uses each mode.
Why a thickness gauge needs the right velocity
A pulse-echo gauge times the round trip and works out thickness as T = c × t ÷ 2 (Technical Notes, Equation 4, p. 3). The gauge cannot know the material, so the thickness it shows is only as good as the velocity it is set to. Suppose a 10.0 mm aluminum plate is measured with the gauge still set for steel 1020, ignoring zero offset. The round trip takes 2 × 10.0 ÷ 6.32 = 3.165 µs, and the gauge shows 5.89 × 3.165 ÷ 2 = 9.32 mm, about 7% thin. Try the same numbers, or correct a reading taken at the wrong velocity, in the ultrasonic thickness calculator.
Try one question
Question 1 of the free 10-question check on UT L2. No signup. About 13 minutes. Most checks include 2 calculation questions, with a calculator on the page. Then ask Echo, the AI study assistant, why the answer is right and the others are wrong.
Discontinuity Detection
A planar reflector gives its highest echo amplitude when the beam strikes it
Press A-D or 1-4 to choose an answer while this question is on screen.
Choose an answer to begin
Wavelength from velocity: λ = v ÷ f
Wavelength is velocity divided by frequency (Technical Notes, Equation 2, p. 2). With velocity in mm/µs and frequency in MHz, the answer comes out in mm. Worked at 5 MHz in steel 1020:
- Longitudinal: 5.89 ÷ 5 = 1.18 mm (0.046 in)
- Shear: 3.24 ÷ 5 = 0.65 mm (0.026 in)
The shear wavelength is shorter because shear velocity is lower. Pick a material preset and a frequency in the UT beam calculator to get the wavelength, near field and beam spread together.
Temperature and alloy change the number
The chart gives typical values, not the velocity of the part in front of you. Evident's thickness gauge tutorial names density and elasticity, composition, grain structure and temperature as the main factors that affect sound velocity. The chart shows the alloy effect already: four steels span 5,660 to 5,890 m/s longitudinal. That is why velocity is calibrated on a reference sample of the material being tested rather than read from a table.
Ultrasonic pulse velocity testing of concrete is a different test on a different material and is not covered here.
Put the numbers to work
Velocity feeds the wavelength, near field, Snell's law and skip distance formulas behind the UT General math. Each formula is worked in the UT Level II formulas guide. Then take the free 10-question check. It covers the UT General exam, needs no signup and explains every answer, so you see which topic to study next.
FAQ
What is the ultrasonic velocity of steel?
For 1020 steel, about 5,890 m/s (0.232 in/µs) longitudinal and 3,240 m/s (0.128 in/µs) shear. Other steels differ a little: 4340 is about 5,850 m/s and stainless 302 about 5,660 m/s longitudinal.
What is the ultrasonic velocity of water?
About 1,480 m/s (0.058 in/µs) at 20 °C. Water carries only longitudinal waves, so it has no shear velocity.
What is the ultrasonic velocity of aluminum?
About 6,320 m/s (0.249 in/µs) longitudinal and 3,130 m/s (0.123 in/µs) shear.
Why is shear wave velocity lower than longitudinal?
A shear wave depends on how strongly a solid resists sideways sliding, and solids resist that less than they resist squeezing. In common metals the shear velocity is roughly half the longitudinal velocity.
Where do our practice questions come from?
Every question is original and written to ASNT's published outline for the Level II General exam.
Sources
Show the list
- Olympus (Evident), Ultrasonic Transducers Technical Notes (2019): Table 2 (p. 11) for every velocity in the chart; Equations 2 (p. 2), 4 (p. 3) and 15 to 17 (p. 8). Checked 21 Nov 2026.
- Evident, Ultrasonic Thickness Gauge Tutorial: Velocity and Zero Calibration, for the factors that affect velocity and velocity calibration on a reference sample. Checked 21 Nov 2026.
Not affiliated with or endorsed by ASNT.
Ask Echo: Am I ready?
Ask Echo before you buy AI your AI study assistant
See what's on the UT L2 exam, test yourself with 5 quick questions, or find the plan that fits you.
The UT L2 course
Available now · instant accessLearn every General exam topic, work the calculations step by step, then prove it on timed exams.
Instant access. Terms and refunds · Secure checkout by Stripe · Billed by Nori Software
What's inside
- 7modules of lessonsEvery task on the outline
- 5full-length timed exams50 questions in 120 minutes each
- 387practice questionsEach one explained
- 5worked calculationsStep by step
- 1week-by-week study planSet to your exam date
Turn a practice answer into a study step. In untimed practice, ask Echo AI about any question you answer, follow up, then see your weakest topics and what to drill next.
- UT, MT and PT bundle$299$108 less than buying the 3 courses separatelyIncludes the UT L2, MT L2 and PT L2 courses
Terms and refunds · Secure checkout by Stripe · Billed by Nori Software
- Question of the dayFree
Every answer comes with a full explanation.
Angle Beam editorial team
Facts come from the sources listed above. If something has changed, tell us and we will correct it.
Your next step
Ready to see where you stand on UT L2?
Free, untimed and scored by domain. No signup. About 13 minutes. Most checks include 2 calculation questions, with a calculator on the page.
Free 10-question checkNDT UT Level II General course. Lessons, timed practice exams and a plan around your exam date.
Get NDT UT Level II General course · $149Want a timed run? Take the free 25-question practice test (about 60 minutes). No email needed.
Free tools for this topic
Prefer paper? Free printables
- Print the study checklist (free PDF). Topics to cover, on one printable page. No email.
- Print a class quiz (free PDF). 6 practice questions with an answer key on page 2.
- Print the flashcards as cut-out cards (free PDF). The free flashcard sample, ready to cut and carry.
From the blog
- UT Level II practice questions with worked answers
- Decibels in ultrasonic testing: the 6 dB and 20 dB rules
- The math behind NDT Level II: algebra, trig and units